Search results

Synergy/MTS Forum

Help Support Synergy/MTS Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. K

    Lynch Box Power Tube Redplates

    Of course, I flip flopped the tubes and the amp worked fine. I guess I will have to just wait it out and see what happens. Thanks.
  2. K

    Lynch Box Power Tube Redplates

    Lynch box has 3 Tungsol 12ax7 preamp tubes and 2 EH 6L6 power tubes in it. Power tube closest to phase inverter red plates once in a while, and man can I hear it thru the speaker when it does. Other power tube is fine. Bias set at 30mv. Should I try new tubes? Are the Tungsol preamp tubes...
  3. K

    Presence Mods?

    The combo has the Super V Eminence. I also run a Nuno NB King cab off of it with Celetion Greenbacks in it. Ohms set at 4. No matter what preamp tubes I put in it, still not as bright as I want it. Thanks.
  4. K

    Presence Mods?

    Are there any mods that can be done to the presence knob to give me more headroom, high end clarity? I have the knob maxed and still want more clarity. I have new preamp tubes installed. This amp(RM50LB)has always seemed dark. Thanks!!
  5. K

    Lynch Box is a Mud Ball

    I have the Grail module. Has anyone modded this module? I know about the C3 change on the PC board. To me, the module has always seemed too muddy. I run the gain at 7, bass at 5, mids at 5, and treble at 8. I tried bass at 3, mids at 3, and highs at 8 for some sucess, but doesn't explain...
  6. K

    Lynch Box is a Mud Ball

    I have both active and non active pickup guitars. They all sound muddy. The power tubes (Svet6550's) have about 10 hrs. on them. The preamp tubes(EH 12ax7's) have not much more on them. The grail module(Ruby12ax7's) probably have the most hrs. on them. Side note: I bought a Vox JS Ice 9...
  7. K

    Lynch Box is a Mud Ball

    In the past week, my Lynch Box has became very muddy. I am guessing that this is a preamp tube issue, but not sure. Which tube would most likely be the culprit? I guess it could be module tubes also. Any help would be much appreciated. Thanks!!
  8. K

    What FX are you using.

    I have tried both Boss Chorus pedals in the loop, and they didn't work. Let me ask you this. If I was to get the DD-20, since it is line level, would that make all pedals after that in the loop line level? Thanks
  9. K

    What FX are you using.

    Ok. Went with a RP1000 from MF just because I always wondered what it would sound like. After playing with it for about an hour, back in the box, and back to MF. Great solid unit, but WAY too much time trying to get where I want to go. I don't mind tap dancing with the stomp boxes because I...
  10. K

    What FX are you using.

    Great!! Thanks for your help.
  11. K

    What FX are you using.

    I play hard rock to metal. I have played for about 30yrs. and have went down both paths with rack units and pedals. Basically, I use delay and sometimes chorus. The LynchBox has the reverb in it, so I am good there. After all these years of playing, really looking to simplify as much as...
  12. K

    What FX are you using.

    Looking for FX unit that doesn't color the amps original sound. I have a Line 6 M9 unit, but it does color my sound, and it also boosts the volume level with some fx and cuts the volume level with othe fx. I haven't ruled out going with the pedal route, but just didn't know what wouldn't color...
  13. K

    Lynch Box Serial Loop Problem

    It did pop without the M9 connected. After the preamp tube change, it didn't pop. I played for about an hour after that. I will put more time into playing tomorrow and see what happens.
  14. K

    Lynch Box Serial Loop Problem

    Run down of what happened today: -Bumped Line 6 M9 pedal into the corner of the amp where the power and standy buttons are. Made a loud pop. Lost half of my volume. -Jiggled all cables on amp. -When unplugging and plugging back in the 1/4's to the serial send/return, this retuned volume to...
  15. K

    Lynch Box Tube Help

    Let me start by saying I purchased the rm50 palamino combo before the Lynch Box combo. It was defective, so had to send it back. Before I sent it back, I played it for about a month. WAY more bottom end. It had the 6L6's in it, and Celestion speaker.
  16. K

    Lynch Box Tube Help

    Just not getting enough bottom end from the EL34L's that are in the Lynch Box Combo. Definitely not looking to get muddy. Are 6550's the way to go, or 6L6, or even something else? Thanks.
  17. K

    Lynch Box Ohm setting

    Thanks for the info. It sounds great as it stands right now. I agree about dialing the amp in. It does take sometime to get the sound where I want it. Of course, this is a good problem to have. Thanks.
  18. K

    Lynch Box Ohm setting

    Have the Lynch Box 50w combo and was wondering what will happen to the amp or speaker if I set the ohm switch to 16ohm instead of the preferred 8ohm setting? I like the crispier high end sound when set at 16ohm, but don't leave it there for long. Amp is new, so speaker isn't even broken in...
  19. K

    Lynch Box Combo Speaker Cable

    I have a defective speaker cable on my Lynch Box. The tip came unsoldered, but temporarily resoldered it. It also seems that the boot on the cable is barely letting the jack plug all the way in causing the slighest touch to the jack to short the speaker out. How do I get a new one? Thanks.
  20. K

    Lynch Box Reverb

    Let's say that i wanted to run a delay in the parallel loop with the reverb tank that comes with the Lynch Box. If I bought something with 2 ins and 2 outs, like the Digitehch Hardwire delay pedal, would I able to run the reverb thru this pedal and get both to work and be able to use the mix...
Top