Recent content by kinder5150

Of course, I flip flopped the tubes and the amp worked fine. I guess I will have to just wait it out and see what happens. Thanks.

Lynch box has 3 Tungsol 12ax7 preamp tubes and 2 EH 6L6 power tubes in it. Power tube closest to phase inverter red plates once in a while, and man can I hear it thru the speaker when it does. Other power tube is fine. Bias set at 30mv. Should I try new tubes? Are the Tungsol preamp tubes...

The combo has the Super V Eminence. I also run a Nuno NB King cab off of it with Celetion Greenbacks in it. Ohms set at 4. No matter what preamp tubes I put in it, still not as bright as I want it. Thanks.

Are there any mods that can be done to the presence knob to give me more headroom, high end clarity? I have the knob maxed and still want more clarity. I have new preamp tubes installed. This amp(RM50LB)has always seemed dark. Thanks!!

I have the Grail module. Has anyone modded this module? I know about the C3 change on the PC board. To me, the module has always seemed too muddy. I run the gain at 7, bass at 5, mids at 5, and treble at 8. I tried bass at 3, mids at 3, and highs at 8 for some sucess, but doesn't explain...

I have both active and non active pickup guitars. They all sound muddy. The power tubes (Svet6550's) have about 10 hrs. on them. The preamp tubes(EH 12ax7's) have not much more on them. The grail module(Ruby12ax7's) probably have the most hrs. on them. Side note: I bought a Vox JS Ice 9...

In the past week, my Lynch Box has became very muddy. I am guessing that this is a preamp tube issue, but not sure. Which tube would most likely be the culprit? I guess it could be module tubes also. Any help would be much appreciated. Thanks!!

I have tried both Boss Chorus pedals in the loop, and they didn't work. Let me ask you this. If I was to get the DD-20, since it is line level, would that make all pedals after that in the loop line level? Thanks

Ok. Went with a RP1000 from MF just because I always wondered what it would sound like. After playing with it for about an hour, back in the box, and back to MF. Great solid unit, but WAY too much time trying to get where I want to go. I don't mind tap dancing with the stomp boxes because I...

Great!! Thanks for your help.

I play hard rock to metal. I have played for about 30yrs. and have went down both paths with rack units and pedals. Basically, I use delay and sometimes chorus. The LynchBox has the reverb in it, so I am good there. After all these years of playing, really looking to simplify as much as...

Looking for FX unit that doesn't color the amps original sound. I have a Line 6 M9 unit, but it does color my sound, and it also boosts the volume level with some fx and cuts the volume level with othe fx. I haven't ruled out going with the pedal route, but just didn't know what wouldn't color...

It did pop without the M9 connected. After the preamp tube change, it didn't pop. I played for about an hour after that. I will put more time into playing tomorrow and see what happens.

Run down of what happened today: -Bumped Line 6 M9 pedal into the corner of the amp where the power and standy buttons are. Made a loud pop. Lost half of my volume. -Jiggled all cables on amp. -When unplugging and plugging back in the 1/4's to the serial send/return, this retuned volume to...

Let me start by saying I purchased the rm50 palamino combo before the Lynch Box combo. It was defective, so had to send it back. Before I sent it back, I played it for about a month. WAY more bottom end. It had the 6L6's in it, and Celestion speaker.